STM32F103VET6 Mini minimum system
Product Description:
This is a ARM core board and based on the main chip STM32F103VET6 , has the following characteristics:
1, onboard the most basic MCU-based circuits, such as crystal oscillator circuit, USB power management circuit and USB interface.
2, the core board leads to all the I / O port resources.
3, with SWD simulation debugging download interface, the interface requires at least three lines to complete the debugging download task, compared to the traditional JTAG debugging has a lot of benefits, here insert a, JTAG now big to eliminate the trend, For example, ST's new M0 series MCU only retains the SWD debug interface, JTAG directly canceled.
4, the use of the current smart phone used by the Mirco USB interface, easy to use, do USB communication and power supply.
5, the core board of the system crystal (8MHz) use high precision high quality and low load NDK's NX5032GA, without the use of low-cost iron crystal.
6, for the STM32 RTC can not afford the problem, we have adopted the official proposal of low-load RTC crystal program, and the use of the Epson brand crystal, and did not use cheap cylindrical crystal.
7, the core board with EEPROM, model AT24C08 convenient core board for data storage.
8, power regulator chip input and output, respectively, placed a large capacity of high-capacity tantalum capacitors, will be in the regulator, filter plays an extraordinary effect, the same we have not found on Taobao than we use the capacity The greater the value of the seller, heaven and earth conscience.
9, with a high quality 2 * 24 / 2.54mm spacing of the double row of pin, to ensure good contact with electrical conductivity, user-friendly core board will be placed on the standard board or breadboard. Paier default welding, the user can choose according to their own needs welding direction.
Chip Introduction:
1, STM32F103VET6
Package Type: LQFP;
Number of pins: 100;
Kernel: Cortex ™ -M3;
Operating frequency: 72MHz;
Storage resources: 512K Byte Flash, 64KByte SRAM;
Interface resources: 3xSPI, 5xUSART, 2xI2C, 1xSDIO, 1xFSMC, 1xCAN, 80xI / O port;
Analog to digital conversion: 3x ADC (12 bits / 16 channels);
Digital-to-analog conversion: 1x DAC (12 bits);
Timer: 4 general timers 2 advanced timers;
Debug download: support JTAG / SWD interface debugging download, support IAP;
Other chip introduction:
2, RT9193-33: 3.3V regulator chip, the maximum 300mA current.
3, AT24C08: 1024Byte x8, high data transfer rate of 400KHz and IIC bus and
Capacity, the number of erase in about 100 million times, the data storage can be 100 years;
Introduction to interfaces:
1, SWD interface: support simulation, download and debugging.
2, Mirco USB interface: power supply and USB communication function, does not support the download.
3, USART1 interface: can be used for USART1 download program, or use USART1
To communicate.
4, MCU pin interface: lead all the I / O port pin, easy to connect with the peripherals.
5,5V and 3.3V power input and output interfaces: commonly used for external power supply, or with other modules
For co-processing
Other device introduction:
1, power LED (PWR): power indicator state, you can determine whether the power supply is stable.
2, user LED (PC13): easy to I / O output test or indicate the program running status.
3, start jump selection programming mode: (1, user flash 2, SRAM 3, system memory).
4, reset button: for the user to reset the chip program.
5,8M crystal: can be set by the frequency to make the system clocked at 72MHz.
6,32.768KHz Crystal: available for built-in RTC, or for calibration.
Distribution information:
1, keil ARM software MDK programming software
2, the core board program Demo (mainly core board test program)
3, the core board technical documentation (mainly related device technical manual)
4, the core board hardware information (mainly circuit diagram)
5, STM32 learning materials (technical manual and reference routines)
